100W Single Output Industrial DIN Rail Power Supply 24V 4.2A

CARACTERISTIQUES :

• Universal AC input / Full range
• Protections: Short circuit / Overload / Over voltage / Over temperature
• Cooling by free air convection
• Can be installed on DIN rail TS-35/7.5 or 15
• Isolation class II
• indicateur LED d'alimentation
• No load power consumption<1W
• 100% full load burn-in test
• 3 years warranty
• POUR L'USAGE PROFESSIONNEL
• Cet appareil doit être installé par un technicien qualifié.

SPECIFICATIONS :

• OUTPUT:
  • tension CC: 24V
  • courant nominal: 4.2A
  • plage de courant: 0 ~ 4.2A
  • RIPPLE & NOISE (max.) Note.2: 150mVp-p
  • plage de réglage de tension: 24 ~ 29V
  • VOLTAGE TOLERANCE Note.3: ±1.0%
  • régulation de ligne: ±1.0%
  • régulation de charge: ±1.0%
  • temps de démarrage, de montée: 2700ms, 80ms/230VAC 2700ms, 80ms/115VAC at full load
  • temps de maintien (typ.): 50ms/230VAC 18ms/115VAC at full load
  • rated power: 100 W
• entrée:
  • plage de tension: 88-264VAC- 124-370VDC
  • FREQUENCY RANGE: 47 ~ 63Hz
  • rendement (typ.): 89%
  • courant CA (typ.): 3A/115VAC 1.6A/230VAC
  • courant d'appel (typ.): COLD START 30A/115VAC 45A/230VAC
• protection:
  • OVERLOAD Note.6:
    • 105 ~ 135% rated output power
    • Protection type : Constant current limiting, recovers automatically after fault condition is removed
  • OVER VOLTAGE:
    • 30 ~ 35V
    • Protection type : Shut down o/p voltage, re-power on to recover
  • OVER TEMPERATURE:
    • 90°C ±15°C (RTH2) detect on heatsink of power transistor
    • Protection type : Shut down o/p voltage, re-power on to recover
• environnement:
  • WORKING TEMP.: -20 ~ +60°C (Refer to "Derating Curve")
  • humidité de service: 20 ~ 90% RH non-condensing
  • STORAGE TEMP., HUMIDITY: -40 ~ +85°C , 10 ~ 95% RH
  • TEMP. COEFFICIENT: ±0.03%/°C (0 ~ 50°C )
  • vibration: Component:10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes- Mounting: Compliance to IEC60068-2-6
    486K
• SAFETY & EMC (Note 4):
  • SAFETY STANDARDS: UL60950-1, TUV EN60950-1 approved, design refer to EN50178
  • tension d'isolation: I/P-O/P:3KVAC
  • ISOLATION RESISTANCE: I/P-O/P:>100M Ohms / 500VDC / 25°C / 70% RH
  • EMC EMISSION: Compliance to EN61204-3, EN55022 Class B, EN61000-3-2,-3
  • EMC IMMUNITY: Compliance to EN61000-4-2, 3, 4, 5, 6, 8, 11, EN55024, EN61000-6-2, EN61204-3, heavy industry level, criteria A
• autres:
  • MTBF: 486K hrs min. MIL-HDBK-217F (25°C )
  • dimensions: 100 x 93 x 56mm
  • PACKING: 0.35Kg- 36pcs/13.6Kg/0.89CUFT

DOCUMENTS :

• Fiche d'information
  
• Fiche d'information
  Consignes de sécurité générales